Usb isolator ebay11/20/2023 ![]() It can be powered from the USB upstream host port providing up to 380mA of isolated power to the downstream port. The USB-ISOLATOR has an LED that indicates the presence of power from the upstream port. Under UL60590-1 the card design meets or exceeds the DC-DC isolator specification. This isolation component has an over 50 year isolation lifespan even if the isolation voltage potential is in excess of 846 volts AC. Our circuit uses a chip-level high-frequency DC-DC isolator which is rated at 5000Vrms for 1 minute under UL 1577. These gaps are rated under IPC-2221B at 1500V (upstream to downstream). The circuit is isolated with a ≥ 300mil gap between all signal and plane layers (upstream to downstream port). Our Tru-Iso™ products are designed under IPC-2221B, UL1577, and UL60950-1. See the Isolation specification in user manual for full details. Robust EFT, Lightning, and ESD protection at ☒0kV on all signal pins (air and contact). Being able to operate at industrial grade temperatures, the USB-ISOLATOR offers its functionality to a wider range of user applications that many competitors’ isolators can’t provide.Ĭareful attention has been paid to isolation design, including extensive keep-out zones and hand-routed circuit paths, as well as component and material selection. This product utilizes a high-performance, low-power USB 2.0 isolator with an operating temperature rated for industrial grade environments. The Signal Smoothing Adapter can be inserted between J-Link and the debug target to overcome signal integrity issues.Description Single Port USB Isolator, Rugged, Industrial Grade, with Tru-Iso™ Signal Isolation Features 4kV Isolation and Industrial Temperature Operation 1" 20-pin Standard connector to 14-pin RX600 JTAG connector.Īdapts from. The adapter can be used to physically connect Flasher Compact to the target without cable.Īdapts from. Right angle female to female adapter with two female 0.1"-pitch 20-pin connectors. Right Angle Female to Female (RAFF) Adapter It can directly be inserted between the J-Link and the debug cable maintaining a 1:1 connection of all debug signals. The Programming Voltage Adapter delivers two externally provided voltages to the target for programming targets with voltage requirements beyond 5 V. 1" 20-pin target connector to Microchip RJ11 modular debug connector. ![]() 1" 6-pin connector.Īdapts from the standard. The Intel FPGA Adapter (formerly J-Link Altera Adapter) connects to the 10-pin 100-mil Intel FPGA JTAG connector providing debug access to FPGA-based MCU cores like the dual-core Arm Cortex-A9 in the Cyclone V devices.Īdapts from 38-pin Mictor connector to standard 20-pin connector.Īdapter for non-standard J-Link Target connection.Īdapts from the standard. Or for manually connecting a J-Link or Flasher to ST Discovery boards. Especially useful when hooking up prototype HW where no final connector is decided yet. 1" 14-pin mating JTAG connector.Īdapts from the standard 20 pin 0.1" connector to a 10-pin row, allowing to connect J-Link or Flasher to target PCBs via flying wires. This adapter allows custom connections/wiring between the 20-pin and 10-pin side.Īdapter to connect a J-Link EDU mini with 0.05"-pitch connector with cable or regular J-Link with standard 20-pin header with an Arduino board of the MKR seriesĪdapter for Arm targets with. 05" 19-pin Cortex-M connector.Īdapts from the standard 20 pin 0.1" connector to the standard 10-pin 0.05" Cortex-M connector that is also used on many non-Cortex-M designs but with non-standard pinout. 05" 10-pin needle pattern.Īdapts from 20-pin, 0.1'' Standard connector to TI 14-pin connector.Īdapts from. 05" 9-pin Cortex-M connector.Īdapts from. 05" 6-pin needle pattern.Īdapts from 20-pin, 0.1'' Standard connector to. 1" 20-pin standard connector to 2mm 20-pin connector.Īdapts from standard 20-pin 0.1" socket to a standard 20-pin 0.1" header on the target side, provides a supply voltage of 5 V.Īdapts from. SuperSpeed USB 3.0 driven debug probe supporting unlimited streaming trace for RISC-V devices, 64MB on-board trace bufferĪdapts from. ![]() SuperSpeed USB 3.0 driven debug probe supporting unlimited streaming trace for Cortex-M devices, 64 MB on-board trace buffer SuperSpeed USB 3.0 driven debug probe supporting unlimited streaming trace for Cortex-M, Cortex-R and Cortex-A devices, 64 MB on-board trace buffer The JTAG/SWD debug probe with USB interface.ĭebug probe in reduced form factor for educational purposes The JTAG/SWD debug probe with WLAN/WiFi interface. Hi-Speed USB 2.0 and Ethernet driven debug probe Includes free software updates and 1 (one) year of email support ![]() J-Link PRO PoE is SEGGER's specialized programming and debug probe for creating test farms.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |